YZR or YZ: The rotor decides how good a motor is

When sizing a motor for a crane or metallurgy drive, most buyers only look at power (kW). But the rotor type matters just as much. At the same rating, the YZR (wound-rotor) and the YZ (squirrel-cage) differ greatly in starting ability, braking and tolerance of frequent start/stop. Pick wrong and you get slow starts or constant over-temperature trips.

YZR vs YZ: Key comparison

ItemYZR (wound-rotor)YZ (squirrel-cage)
RotorWound-rotor, slip rings for resistanceSquirrel-cage, simple
Starting torqueHighLower
Starting currentLowHigher
Frequent start / reversingExcellentFair
MaintenanceSlip rings / brushes to maintainMaintenance-free
Frames / powerYZR112M-400L2, 1.5-200kWYZ112M-250M1, 1.1-37kW
Base dutyS3-40%S3-40%
Voltage / protection380V / IP44-IP55380V / IP44-IP55

How to choose: match your duty

Choose YZR (wound-rotor) for crane main hoists, metallurgy equipment and mill auxiliaries with frequent starting, reversing and braking. Wound-rotor gives high starting torque with low starting current, so reversing and braking are comfortable.Choose YZ (squirrel-cage) for auxiliaries, conveyors and winches that start infrequently - robust, maintenance-free and lower cost.

Need a brake for positioning? YZE / YZRE

If the machine needs accurate positioning or reliable stopping (inclines, overhead cranes, e-stops), add a DC electromagnetic brake to the YZ/YZR platform:

  • YZE: YZ squirrel-cage + electromagnetic brake, reliable and adjustable, 0.75-45kW.
  • YZRE: YZR wound-rotor + electromagnetic brake, combining high starting torque with reliable braking.

Both brake DC voltages are 170V, fed from the 380V supply.

Real figures from the sample

For YZR, frames go from YZR112M (1.5kW) up to YZR400L2 (200kW), with max-torque / rated-torque ratio around 2.3-3.3 - the mark of a wound-rotor's overload capacity. The YZ cage runs 69.5%-85% efficiency, locked-torque ratio about 2.4-3.1, and weighs 58-462 kg. Compare these on the YZR series and YZ series pages.

Selection steps

  1. Confirm the load: crane main hoist, auxiliary, or continuous metallurgy.
  2. Set the duty class (M level) and whether start/stop is frequent.
  3. Need braking or positioning? Choose YZE or YZRE.
  4. Set voltage (380V), protection (IP44/IP55), cooling and mounting dimensions.

FAQ

What is the main difference between YZR and YZ motors?

YZR is wound-rotor, so rotor resistance gives high starting torque and low starting current for frequent starting/reversing/braking; YZ is squirrel-cage, robust and maintenance-free but with lower starting torque and higher starting current.

Why do crane and metallurgy motors use S3-40% duty?

Crane and metallurgy machines start, brake and run briefly rather than continuously. S3-40% means 40% duty cycle, so you check temperature rise for that intermittent pattern.

Which is better for frequent reversing, YZR or YZ?

YZR (wound-rotor) is better - high starting torque and strong braking; YZ (squirrel-cage) suits auxiliaries that start infrequently.

What is the difference between YZE/YZRE brake motors and a standard motor?

YZE adds a DC electromagnetic brake to the YZ squirrel-cage, and YZRE adds the brake to the YZR wound-rotor. Both use a 170V DC brake, reliable and adjustable.

What is the largest YZR power available?

From the sample, YZR frames YZR112M to YZR400L2 cover 1.5-200kW; YZ frames YZ112M to YZ250M1 cover 1.1-37kW.